How to Install a Tub (Step By Step).
How to Install a Tub (Step By Step).
Blog Article
Here below you can discover a good deal of sound insights around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is easily easily accessible, the job can relocate quickly; if you have to open a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the job and fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you start. Opportunities are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new bathtub in your shower room if you have actually already gotten a brand-new bathtub and also don't require to change the plan of your previous water supply pipes.
Your devices and material list should comprise the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bathtub and also check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used a minimum of once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can crack fairly early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on How to Install a Bathtub, I figured sharing that topic was a great idea. Are you aware of somebody else who is interested in the subject? Do not hesitate to promote it. Thanks a lot for your time. Visit us again soon.
Source Report this page